Відео

that time i couldn't afford to buy one. sorry :(

What fhone you got now?​@@AshiqsTheory

Yes. Thanks for reaching out. Actually, you can use the accelerometer value. but in that time I had MPU6050 in my home so I just made it with it. you can take acetometer values to build one as well.

@@AshiqsTheory my point is Linear Movement of my hand should be reflected as movement of the cursor on the monitor . This can be achieved using only accelerometer values present in mpu6050 right ? ie float ax = mpu6050.getAccX(); float ay = mpu6050.getAccY(); Move(ax,ay) . Can i do like this . Correct me if i am mistaken

@@alenninan5524 yeah, just take the X-axis and Y-axis values and freeze the Z-axis.

@@AshiqsTheory so is it accurate and without timelag (if u had tested with accelerometer and gyro seprately )? Since i worked with gyro and the cursor was moving on its own even when my hand/finger was stationary ? I do not need these sort of problems with acceleromwter .thts y asked

@@alenninan5524 well, the reason behind auto movement is because it was not calibrated properly. I made another video on how to calibrate it, you may search in my channel and find that one. You have to calibrate and put a specific value to stop the automatic movement

<3 Indeed

Thanks <3

Keep sharing loves <3

Well, do not take power from Arduino board to the Bluetooth Module. Connect the power pin of the Bluetooth module separately, so that it has adequate power supply. Because Arduino dev. boards can't. provide sufficient current supply to Bluetooth module.

@@AshiqsTheory thank u so much … i powerd the bleutooth directly from the l298n motor driver and it works fine without disconnecting so thank u so much brother god bless u

@@malekkh-ww6bj Pray for me so that I can get married ASAP! <3

@@AshiqsTheory i really hope that brother and i hope u can find good and beautiful wife 🙏

@@malekkh-ww6bj Ameen! <3

No device should should only support 60 Hz, it should have support for both 50 Hz and 60 Hz. See if it is written as 50/60 Hz then it's good t use. Also, look for the voltage rating, for example, you can't bring a Japanese-made electrical appliance that only runs on 100V. So make sure the device can run on 220V AC supply as well.

Glad to help <3

Thank you, Mr. Calendar 📆

No. Frequency is not dependent on voltage or current

What is the Voltage rating?

@AshiqsTheory salam bro আমি microwave details দিলাম deken bangladesh colve ki na voltage 230-240v-50hz microwave power input 1100_1150w microwave power outputs 650_700w frequency-2450_hhz bro please answer দিবেন এইটা bangladesh আনলে ki colve naki ফায়ার hove

Can you show me please ? A photo will work. The maximum limit for the power factor is 1. Maybe you've seen something else.

Watt is the unit of power which is a cross product of Voltage(V) and Current(I). So, in order to figure out the power consumption, except for 230V you'll need to measure the current consuming by the load. i.e.: for a single phase 230V, if hte load is consuming 0.5A of current approximately then the power consumption would be = 230 x 0.5 x PF (Power factor) [Let's say PF is 1.00] = 230 x 0.5 x 1.00 = 115 Watt. Hope you got it! Now 50/60Hz is already explained in the video. You can get power from this equation as well = I^2 x R x PF

Thanks !

Appreciate it ♥️

That'll be added to my success diary ♥️ Appreciate it!

Have a bright success ahead 😊 !

Three things can happen. 1. Bad connection - Loose wires 2. Burned BT module 3. Battery voltage is not sufficient N.B.: if your battery is supplying less current then the BT will turn on and disconnect. But in your case it is not even turning on. So you better look into these matters.

@@AshiqsTheory thanksss dada for ur replyyy , i will now work on it😊

Anytime

♥️♥️♥️

What do you need a Servo for ?

Man, cut it in clear. I didn't understand a single thing that you've just said. Tell me the entire picture!

Yes. Use powerbank. But provide a power supply to the HC-05 separately. Do not take any power bus from Arduino or other boards.

pretty fair point!

Basically, I'm not a keyboard extremist. But I like to test them ot. For sure if I get a chance I'll make some more with different switches.

@@AshiqsTheory I appreciate what you doing my bro. If you're interested about the keyboard world save some and get a hotswappable custom keyboard. Your life will change ❤️😁

@@rahishadab9415 this one is a hot swappable. Go for the specs of Bajeal K100. I tried the Red and one type of Akko in it. Worked perfectly. But I need the tactile repsonse for my type of work ! Thanks anyway!

Depends on which Refrigerator. Just read the Wattage on the printed sticker and match whether your power strip can take it or not. But in general, it is okay to use power strips/multiplug inlet. But better practice would be using the Wall Sockets which will give much more stable connectivity!

I got well years ago!

Ensure 5V 1A(or more) current

@@AshiqsTheory brother I have messaged you in Facebook please do reply...

First go to a store, show the video to the shopkeeper and ask if they have it

এবং 60 Hz থেকে কি 50 Hz করা যাবে,

Go through this article. You'll find all your answers www.gohz.com/can-a-50hz-machine-work-on-60hz-power-system#:~:text=Electrical%20machines%20designed%20for%2050Hz,run%20in%2050Hz%20power%20supply.

Yes, you can get a frequency converter, but I guess they're not that cheap at all !

Connect adequate power supply for the Arduino and Bluetooth. Otherwise it'll keep disconnecting

@@AshiqsTheory Thank you very much

You're always welcome!

Thanks 🙏

Thanks a lot!

Thank you for the response. Can you please teach what they are actually? I'll appreciate!

What do you need a DC motor for ?

@@AshiqsTheory dc motor for r alarm ball

I'm sorry, but i didn't understand a thing you're saying. Please clarify your question if possible. Thanks 😐

Me? Bengali

Basically CT-PT could be used for too many factors such as fault detection, finding load current, load power and few others. It's not necessary to know the supply V o I . But you gotta know the ratio of the CT or PT that you'll be using!

Thank you for the time amd effort!

You're welcome 😀

Thank you

Thanks a ton! Stay SUBSCRIBED!

Will try best!

And what does that mean! 😆